[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
[debian-users:31279] Re: NIC の設定が分りません
西です。
武藤さん始めまして。「徹底入門」読ませてもらっています。
IRQですが．．以下の様になっています。
Bus No. Device No. Func No. Vender/Device Class Device Class IRQ
----------------------------------------------------------------------------
0 31 1 8086 244B 0101 IDE Controller 14
0 31 3 8086 2443 0C05 SMBus Controller NA
0 31 5 8086 2445 0401 Multimedia Device 9
1 0 0 1002 475A 0300 Display Controller 5
2 2 0 134D 7897 0703 Simple CPMM.Controller 9
2 3 0 10EC 8139 0270 Network Controller 11
ACPI Controller 9
lspci -vv 結果を全て載せさせていただきますと。
00:00.0 Host bridge: Intel Corporation: Unknown device 1130 (rev 02)
Subsystem: Intel Corporation: Unknown device 1130
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 0 set
Region 0: Memory at d0000000 (32-bit, prefetchable)
Capabilities: [88] #09 [f104]
Capabilities: [a0] AGP version 2.0
Status: RQ=31 SBA+ 64bit- FW- Rate=421
Command: RQ=0 SBA- AGP- 64bit- FW- Rate=
00:01.0 PCI bridge: Intel Corporation: Unknown device 1131 (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 set
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
I/O behind bridge: 00009000-00009fff
Memory behind bridge: d4000000-d5ffffff
Prefetchable memory behind bridge: d6000000-d6ffffff
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
00:1e.0 PCI bridge: Intel Corporation: Unknown device 244e (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0 set
Bus: primary=00, secondary=02, subordinate=02, sec-latency=32
I/O behind bridge: 0000a000-0000afff
Memory behind bridge: d7000000-d8ffffff
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
00:1f.0 ISA bridge: Intel Corporation: Unknown device 2440 (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0 set
00:1f.1 IDE interface: Intel Corporation: Unknown device 244b (rev 02) (prog-if 80 [Master])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0 set
Region 4: I/O ports at f000
00:1f.3 SMBus: Intel Corporation: Unknown device 2443 (rev 02)
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 0
Region 4: I/O ports at 5000
00:1f.5 Multimedia audio controller: Intel Corporation: Unknown device 2445 (rev 02)
Subsystem: Unknown device 414c:4326
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0 set
Interrupt: pin B routed to IRQ 9
Region 0: I/O ports at b800
Region 1: I/O ports at bc00
01:00.0 VGA compatible controller: ATI Technologies Inc 3D Rage IIC AGP (rev 7a) (prog-if 00 [VGA])
Subsystem: ATI Technologies Inc: Unknown device 008800:00.0 Host bridge: Intel Corporation: Unknown
device 1130 (rev 02)
Subsystem: Intel Corporation: Unknown device 1130
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 0 set
Region 0: Memory at d0000000 (32-bit, prefetchable)
Capabilities: [88] #09 [f104]
Capabilities: [a0] AGP version 2.0
Status: RQ=31 SBA+ 64bit- FW- Rate=421
Command: RQ=0 SBA- AGP- 64bit- FW- Rate=
00:01.0 PCI bridge: Intel Corporation: Unknown device 1131 (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 set
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
I/O behind bridge: 00009000-00009fff
Memory behind bridge: d4000000-d5ffffff
Prefetchable memory behind bridge: d6000000-d6ffffff
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
00:1e.0 PCI bridge: Intel Corporation: Unknown device 244e (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0 set
Bus: primary=00, secondary=02, subordinate=02, sec-latency=32
I/O behind bridge: 0000a000-0000afff
Memory behind bridge: d7000000-d8ffffff
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
00:1f.0 ISA bridge: Intel Corporation: Unknown device 2440 (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0 set
00:1f.1 IDE interface: Intel Corporation: Unknown device 244b (rev 02) (prog-if 80 [Master])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0 set
Region 4: I/O ports at f000
00:1f.3 SMBus: Intel Corporation: Unknown device 2443 (rev 02)
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 0
Region 4: I/O ports at 5000
00:1f.5 Multimedia audio controller: Intel Corporation: Unknown device 2445 (rev 02)
Subsystem: Unknown device 414c:4326
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0 set
Interrupt: pin B routed to IRQ 9
Region 0: I/O ports at b800
Region 1: I/O ports at bc00
01:00.0 VGA compatible controller: ATI Technologies Inc 3D Rage IIC AGP (rev 7a) (prog-if 00 [VGA])
Subsystem: ATI Technologies Inc: Unknown device 0088
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 8 min, 32 set, cache line size 08
Interrupt: pin A routed to IRQ 5
Region 0: Memory at d6000000 (32-bit, prefetchable)
Region 1: I/O ports at 9000
Region 2: Memory at d5000000 (32-bit, non-prefetchable)
Capabilities: [5c] Power Management version 1
Flags: PMEClk- AuxPwr- DSI- D1- D2- PME-
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
02:02.0 Modem: PCTel Inc: Unknown device 7897 (rev 02) (prog-if 04 [Hayes/16750])
Subsystem: PCTel Inc: Unknown device 0001
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR+
Interrupt: pin A routed to IRQ 9
Region 0: I/O ports at a000
Capabilities: [40] Power Management version 2
Flags: PMEClk- AuxPwr- DSI+ D1- D2+ PME+
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
02:03.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RT8139 (rev 10)
Subsystem: Realtek Semiconductor Co., Ltd. RT8139
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR+
Latency: 32 min, 64 max, 32 set
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at a400
Region 1: Memory at d8000000 (32-bit, non-prefetchable)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 8 min, 32 set, cache line size 08
Interrupt: pin A routed to IRQ 5
Region 0: Memory at d6000000 (32-bit, prefetchable)
Region 1: I/O ports at 9000
Region 2: Memory at d5000000 (32-bit, non-prefetchable)
Capabilities: [5c] Power Management version 1
Flags: PMEClk- AuxPwr- DSI- D1- D2- PME-
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
02:02.0 Modem: PCTel Inc: Unknown device 7897 (rev 02) (prog-if 04 [Hayes/16750])
Subsystem: PCTel Inc: Unknown device 0001
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR+
Interrupt: pin A routed to IRQ 9
Region 0: I/O ports at a000
Capabilities: [40] Power Management version 2
Flags: PMEClk- AuxPwr- DSI+ D1- D2+ PME+
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
02:03.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RT8139 (rev 10)
Subsystem: Realtek Semiconductor Co., Ltd. RT8139
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR+
Latency: 32 min, 64 max, 32 set
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at a400
Region 1: Memory at d8000000 (32-bit, non-prefetchable)
マザーボードのマニュアルにAGPスロットとPCIスロット1は、
IRQが共通となっているとあるため。
LANカードはPCIスロット3に挿してあります。
PCIスロット2には、モデムカードが挿してあります。
ドライバーですが、LANカードに附属のFDにドライバのソースがありましたが、
カーネルソースに含まれる物よりタイムスタンプが古い物でしたので、
カーネルソースの物を使用しています。
IOポートアドレスの重複だろうかとか、色々考えていますが知識がありません。
ほかに載せるべき情報がありましたら是非教えて下さい。
ご指導のほどお願いいたします。