[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
[debian-users:02239] [Q]X setting for FMV5166D7
森山＠九州大学です
またもやDebianでなくLinux genericな質問で恐縮ですが(^_^;)
Unix User付録のDebian1.3.1をFMV5166D7にインストールしたのですが
Ｘの設定がうまく行きません(一度はうまく行ったのですが画面が大きすぎて
ディスプレイに収まりませんでしたのでいじっていたら設定がわからなく
なりました(T_T)）
最初にprobeしたときは，Ｓ３ ＶＩＲＧＥ／ＶＸだったので
ＸＦ８６Ｓｅｔｕｐのcard listでＳ３ ＶＩＲＧＥ／ＶＸを選びましたが，
画面にゴーストが出ます．
以下にＳ３ Ｓ３Ｖサーバーで設定した場合のX -probeonlyの結果を
付けます（これも画面にゴーストが出ます）
------------------------------------------------------------------------------
XFree86 Version 3.3 / X Window System
(protocol Version 11, revision 0, vendor release 6300)
Release Date: Jun 2 1997
If the server is older than 6-12 months, or if your card is newer
than the above date, look for a newer version before reporting
problems. (see http://www.XFree86.Org/FAQ)
Operating System: Linux 2.0.21 i486 [ELF]
Configured drivers:
SVGA: server for SVGA graphics adaptors (Patchlevel 0):
NV1, STG2000, ET4000, ET4000W32, ET4000W32i, ET4000W32i_rev_b,
ET4000W32i_rev_c, ET4000W32p, ET4000W32p_rev_a, ET4000W32p_rev_b,
ET4000W32p_rev_c, ET4000W32p_rev_d, ET6000, et3000, pvga1, wd90c00,
wd90c10, wd90c30, wd90c24, wd90c31, wd90c33, gvga, ati, sis86c201,
sis86c202, sis86c205, tvga8200lx, tvga8800cs, tvga8900b, tvga8900c,
tvga8900cl, tvga8900d, tvga9000, tvga9000i, tvga9100b, tvga9200cxr,
tgui9320lcd, tgui9400cxi, tgui9420, tgui9420dgi, tgui9430dgi,
tgui9440agi, tgui96xx, cyber938x, clgd5420, clgd5422, clgd5424,
clgd5426, clgd5428, clgd5429, clgd5430, clgd5434, clgd5436, clgd5446,
clgd5480, clgd5462, clgd5464, clgd5465, clgd6205, clgd6215, clgd6225,
clgd6235, clgd7541, clgd7542, clgd7543, clgd7548, clgd7555, ncr77c22,
ncr77c22e, cpq_avga, mga2064w, mga1064sg, oti067, oti077, oti087,
oti037c, al2101, ali2228, ali2301, ali2302, ali2308, ali2401, cl6410,
cl6412, cl6420, cl6440, video7, ct65520, ct65525, ct65530, ct65535,
ct65540, ct65545, ct65546, ct65548, ct65550, ct65554, ct64200,
ct64300, ark1000vl, ark1000pv, ark2000pv, ark2000mt, mx, realtek,
AP6422, AT24, s3_virge, generic
(using VT number 7)
XF86Config: /etc/X11/XF86Config
(**) stands for supplied, (--) stands for probed/default values
(**) XKB: rules: "xfree86"
(**) XKB: model: "jp106"
(**) XKB: layout: "jp"
(**) Mouse: type: PS/2, device: /dev/psaux, baudrate: 1200
(**) SVGA: Graphics device ID: "Primary Card"
(**) SVGA: Monitor ID: "Primary Monitor"
(--) SVGA: Mode "320x240" needs vert refresh rate of 60.07 Hz. Deleted.
Warning: The directory "/usr/X11R6/lib/X11/fonts/100dpi" does not exist.
Entry deleted from font path.
Warning: The directory "/usr/X11R6/lib/X11/fonts/Type1" does not exist.
Entry deleted from font path.
Warning: The directory "/usr/X11R6/lib/X11/fonts/Speedo" does not exist.
Entry deleted from font path.
Warning: The directory "/usr/X11R6/lib/X11/fonts/100dpi" does not exist.
Entry deleted from font path.
(**) FontPath set to
"/usr/X11R6/lib/X11/fonts/misc:unscaled,/usr/X11R6/lib/X11/fonts/75dpi:unsca
led,/usr/X11R6/lib/X11/fonts/misc,/usr/X11R6/lib/X11/fonts/75dpi"
(--) SVGA: PCI: S3 ViRGE/VX rev 2, Memory @ 0x08000000
(--) SVGA: S3V: ViRGE/VX rev 2, Linear FB @ 0x08000000
(--) SVGA: Detected S3 ViRGE/VX
(--) SVGA: using driver for chipset "s3_virge"
(--) SVGA: videoram: 2048k
(--) SVGA: Ramdac speed: 220 MHz
(--) SVGA: Detected current MCLK value of 54.886 MHz
(--) SVGA: chipset: s3_virge
(--) SVGA: videoram: 2048k
(**) SVGA: Using 8 bpp, Depth 8, Color weight: 666
(--) SVGA: Maximum allowed dot-clock: 220.000 MHz
(**) SVGA: Mode "640x480": mode clock = 25.180
(--) SVGA: There is no mode definition named "320x240"
(--) SVGA: Removing mode "320x240" from list of valid modes.
(--) SVGA: Virtual resolution set to 640x480
(--) SVGA: SpeedUp code selection modified because virtualX != 1024
------------------------------------------------------------------------------
それとdebianで，Ｘが自動で立ち上がらないようにするには
どこをいじれば良いでしょうか？
/etc/initd以下ですか？
よろしくお願いします
Toshiyuki MORIYAMA
Civil Eng.,Kyushu Univ.,
Hakozaki Higashi-ku
Fukuoka-city
812-81 Japan