[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

[debian-users:31279] Re: NIC の設定が分りません



西です。
武藤さん始めまして。「徹底入門」読ませてもらっています。

IRQですが..以下の様になっています。

Bus No. Device No. Func No. Vender/Device  Class  Device Class           IRQ
----------------------------------------------------------------------------

0       31         1         8086  244B    0101   IDE Controller          14
0       31         3         8086  2443    0C05   SMBus Controller        NA
0       31         5         8086  2445    0401   Multimedia Device        9
1       0          0         1002  475A    0300   Display Controller       5
2       2          0         134D  7897    0703   Simple CPMM.Controller   9
2       3          0         10EC  8139    0270   Network Controller      11
                                                  ACPI Controller          9

lspci -vv 結果を全て載せさせていただきますと。

00:00.0 Host bridge: Intel Corporation: Unknown device 1130 (rev 02)
	Subsystem: Intel Corporation: Unknown device 1130
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
	Latency: 0 set
	Region 0: Memory at d0000000 (32-bit, prefetchable)
	Capabilities: [88] #09 [f104]
	Capabilities: [a0] AGP version 2.0
		Status: RQ=31 SBA+ 64bit- FW- Rate=421
		Command: RQ=0 SBA- AGP- 64bit- FW- Rate=

00:01.0 PCI bridge: Intel Corporation: Unknown device 1131 (rev 02) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
	Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 32 set
	Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
	I/O behind bridge: 00009000-00009fff
	Memory behind bridge: d4000000-d5ffffff
	Prefetchable memory behind bridge: d6000000-d6ffffff
	BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-

00:1e.0 PCI bridge: Intel Corporation: Unknown device 244e (rev 02) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
	Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0 set
	Bus: primary=00, secondary=02, subordinate=02, sec-latency=32
	I/O behind bridge: 0000a000-0000afff
	Memory behind bridge: d7000000-d8ffffff
	BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-

00:1f.0 ISA bridge: Intel Corporation: Unknown device 2440 (rev 02)
	Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0 set

00:1f.1 IDE interface: Intel Corporation: Unknown device 244b (rev 02) (prog-if 80 [Master])
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0 set
	Region 4: I/O ports at f000

00:1f.3 SMBus: Intel Corporation: Unknown device 2443 (rev 02)
	Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Interrupt: pin B routed to IRQ 0
	Region 4: I/O ports at 5000

00:1f.5 Multimedia audio controller: Intel Corporation: Unknown device 2445 (rev 02)
	Subsystem: Unknown device 414c:4326
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0 set
	Interrupt: pin B routed to IRQ 9
	Region 0: I/O ports at b800
	Region 1: I/O ports at bc00

01:00.0 VGA compatible controller: ATI Technologies Inc 3D Rage IIC AGP (rev 7a) (prog-if 00 [VGA])
	Subsystem: ATI Technologies Inc: Unknown device 008800:00.0 Host bridge: Intel Corporation: Unknown
device 1130 (rev 02)
	Subsystem: Intel Corporation: Unknown device 1130
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
	Latency: 0 set
	Region 0: Memory at d0000000 (32-bit, prefetchable)
	Capabilities: [88] #09 [f104]
	Capabilities: [a0] AGP version 2.0
		Status: RQ=31 SBA+ 64bit- FW- Rate=421
		Command: RQ=0 SBA- AGP- 64bit- FW- Rate=

00:01.0 PCI bridge: Intel Corporation: Unknown device 1131 (rev 02) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
	Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 32 set
	Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
	I/O behind bridge: 00009000-00009fff
	Memory behind bridge: d4000000-d5ffffff
	Prefetchable memory behind bridge: d6000000-d6ffffff
	BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-

00:1e.0 PCI bridge: Intel Corporation: Unknown device 244e (rev 02) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
	Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0 set
	Bus: primary=00, secondary=02, subordinate=02, sec-latency=32
	I/O behind bridge: 0000a000-0000afff
	Memory behind bridge: d7000000-d8ffffff
	BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-

00:1f.0 ISA bridge: Intel Corporation: Unknown device 2440 (rev 02)
	Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0 set

00:1f.1 IDE interface: Intel Corporation: Unknown device 244b (rev 02) (prog-if 80 [Master])
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0 set
	Region 4: I/O ports at f000

00:1f.3 SMBus: Intel Corporation: Unknown device 2443 (rev 02)
	Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Interrupt: pin B routed to IRQ 0
	Region 4: I/O ports at 5000

00:1f.5 Multimedia audio controller: Intel Corporation: Unknown device 2445 (rev 02)
	Subsystem: Unknown device 414c:4326
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0 set
	Interrupt: pin B routed to IRQ 9
	Region 0: I/O ports at b800
	Region 1: I/O ports at bc00

01:00.0 VGA compatible controller: ATI Technologies Inc 3D Rage IIC AGP (rev 7a) (prog-if 00 [VGA])
	Subsystem: ATI Technologies Inc: Unknown device 0088
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 8 min, 32 set, cache line size 08
	Interrupt: pin A routed to IRQ 5
	Region 0: Memory at d6000000 (32-bit, prefetchable)
	Region 1: I/O ports at 9000
	Region 2: Memory at d5000000 (32-bit, non-prefetchable)
	Capabilities: [5c] Power Management version 1
		Flags: PMEClk- AuxPwr- DSI- D1- D2- PME-
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

02:02.0 Modem: PCTel Inc: Unknown device 7897 (rev 02) (prog-if 04 [Hayes/16750])
	Subsystem: PCTel Inc: Unknown device 0001
	Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR+
	Interrupt: pin A routed to IRQ 9
	Region 0: I/O ports at a000
	Capabilities: [40] Power Management version 2
		Flags: PMEClk- AuxPwr- DSI+ D1- D2+ PME+
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

02:03.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RT8139 (rev 10)
	Subsystem: Realtek Semiconductor Co., Ltd. RT8139
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR+
	Latency: 32 min, 64 max, 32 set
	Interrupt: pin A routed to IRQ 11
	Region 0: I/O ports at a400
	Region 1: Memory at d8000000 (32-bit, non-prefetchable)



	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 8 min, 32 set, cache line size 08
	Interrupt: pin A routed to IRQ 5
	Region 0: Memory at d6000000 (32-bit, prefetchable)
	Region 1: I/O ports at 9000
	Region 2: Memory at d5000000 (32-bit, non-prefetchable)
	Capabilities: [5c] Power Management version 1
		Flags: PMEClk- AuxPwr- DSI- D1- D2- PME-
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

02:02.0 Modem: PCTel Inc: Unknown device 7897 (rev 02) (prog-if 04 [Hayes/16750])
	Subsystem: PCTel Inc: Unknown device 0001
	Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR+
	Interrupt: pin A routed to IRQ 9
	Region 0: I/O ports at a000
	Capabilities: [40] Power Management version 2
		Flags: PMEClk- AuxPwr- DSI+ D1- D2+ PME+
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

02:03.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RT8139 (rev 10)
	Subsystem: Realtek Semiconductor Co., Ltd. RT8139
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR+
	Latency: 32 min, 64 max, 32 set
	Interrupt: pin A routed to IRQ 11
	Region 0: I/O ports at a400
	Region 1: Memory at d8000000 (32-bit, non-prefetchable)

マザーボードのマニュアルにAGPスロットとPCIスロット1は、
IRQが共通となっているとあるため。
LANカードはPCIスロット3に挿してあります。
PCIスロット2には、モデムカードが挿してあります。

ドライバーですが、LANカードに附属のFDにドライバのソースがありましたが、
カーネルソースに含まれる物よりタイムスタンプが古い物でしたので、
カーネルソースの物を使用しています。

IOポートアドレスの重複だろうかとか、色々考えていますが知識がありません。

ほかに載せるべき情報がありましたら是非教えて下さい。
ご指導のほどお願いいたします。