[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
[debian-users:37602] Re: ネットワークに繋げたい
薄井です。
松岡さん、ありがとうございます。
#その前に、
#何通も同じメールを出してしまい、失礼致しました。
#気をつけます。
>
> 以下の情報について、ご呈示お願いします。
>
> ・どうしても、DHCPサーバーからIPアドレスを自動的に取得せねばならないか？
> 手動でもよいのか？
私が契約しているCATVは、
IPアドレス
ゲートウェイ
サブネットマスク
ネームサーバ
をDHCP手順にて自動的に取得と書いてあります。
ですので、DHCPサーバを使います。
また、自動的か手動かは、手動でかまいません。
（欲をいえば、自動がいいのですが（笑））
以下は、Knoppixでの結果を表示します。
これで上手くいったら、その結果をwoodyのインストールに役立てます。
> ・$/sbin/lspci -vvの出力結果。特に、Ethernet controllerの部分
抜き出します。
00:0b.0 Ethernet controller: Intel Corp. 82557 [Ethernet Pro 100] (rev 02)
Subsystem: Intel Corp. EtherExpress PRO/100B (TX)
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (2000ns min, 14000ns max)
Interrupt: pin A routed to IRQ 0
Region 0: Memory at e3000000 (32-bit, prefetchable) [disabled] [size=4K]
Region 1: I/O ports at b000 [disabled] [size=32]
Region 2: Memory at e0000000 (32-bit, non-prefetchable) [disabled] [size=1M]
Expansion ROM at <unassigned> [disabled] [size=1M]
>
> ・$dmesgの出力結果。特に、eth0：の部分
$dmesg|grep eth0
としたところ、何も返してくれませんでした。
$dmesg
Linux version 2.4.19-xfs (root@Knoppix) (gcc version 2.95.4 20011002 (Debian prerelease)) #2 SMP Sam Aug 3 16:51:33 CEST 2002
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 0000000027ffc000 (usable)
BIOS-e820: 0000000027ffc000 - 0000000027fff000 (ACPI data)
BIOS-e820: 0000000027fff000 - 0000000028000000 (ACPI NVS)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
639MB LOWMEM available.
Advanced speculative caching feature not present
On node 0 totalpages: 163836
zone(0): 4096 pages.
zone(1): 159740 pages.
zone(2): 0 pages.
Kernel command line: lang=ja ramdisk_size=100000 init=/etc/init noapic apm=power-off hda=scsi hdb=scsi hdc=scsi hdd=scsi hde=scsi hdf=scsi hdg=scsi hdh=scsi vga=791 initrd=miniroot.gz quiet BOOT_IMAGE=knoppix BOOT_IMAGE=vmlinuz
ide_setup: hda=scsi
ide_setup: hdb=scsi
ide_setup: hdc=scsi
ide_setup: hdd=scsi
ide_setup: hde=scsi
ide_setup: hdf=scsi
ide_setup: hdg=scsi
ide_setup: hdh=scsi
Local APIC disabled by BIOS -- reenabling.
Found and enabled local APIC!
Initializing CPU#0
Detected 451.034 MHz processor.
Console: colour dummy device 80x25
Calibrating delay loop... 897.84 BogoMIPS
Memory: 645104k/655344k available (1257k kernel code, 9852k reserved, 489k data, 124k init, 0k highmem)
Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
Inode cache hash table entries: 65536 (order: 7, 524288 bytes)
Mount-cache hash table entries: 16384 (order: 5, 131072 bytes)
Buffer-cache hash table entries: 65536 (order: 6, 262144 bytes)
Page-cache hash table entries: 262144 (order: 8, 1048576 bytes)
CPU: Before vendor init, caps: 0383fbff 00000000 00000000, vendor = 0
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 512K
CPU: After vendor init, caps: 0383fbff 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: 0383fbff 00000000 00000000 00000000
CPU: Common caps: 0383fbff 00000000 00000000 00000000
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
Checking for popad bug... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch (rgooch@xxxxxxxxxxxxx)
mtrr: detected mtrr type: Intel
CPU: Before vendor init, caps: 0383fbff 00000000 00000000, vendor = 0
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 512K
CPU: After vendor init, caps: 0383fbff 00000000 00000000 00000000
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: 0383fbff 00000000 00000000 00000000
CPU: Common caps: 0383fbff 00000000 00000000 00000000
CPU0: Intel Pentium III (Katmai) stepping 03
per-CPU timeslice cutoff: 1461.42 usecs.
SMP motherboard not detected.
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 451.0420 MHz.
..... host bus clock speed is 100.2313 MHz.
cpu: 0, clocks: 1002313, slice: 501156
CPU0<T0:1002304,T1:501136,D:12,S:501156,C:1002313>
Waiting on wait_init_idle (map = 0x0)
All processors have done init_idle
PCI: PCI BIOS revision 2.10 entry at 0xf08b0, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Using IRQ router PIIX [8086/7110] at 00:04.0
Limiting direct PCI/PCI transfers.
isapnp: Scanning for PnP cards...
isapnp: SB audio device quirk - increasing port range
isapnp: Card 'Creative ViBRA16X PnP'
isapnp: 1 Plug & Play card detected total
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
VFS: Disk quotas vdquot_6.5.1
vesafb: framebuffer at 0xe1000000, mapped to 0xe880d000, size 8192k
vesafb: mode is 1024x768x16, linelength=2048, pages=4
vesafb: protected mode interface info at c000:4785
vesafb: scrolling: redraw
vesafb: directcolor: size=0:5:6:5, shift=0:11:5:0
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
pty: 256 Unix98 ptys configured
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PIIX4: IDE controller on PCI bus 00 dev 21
PIIX4: chipset revision 1
PIIX4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xb800-0xb807, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xb808-0xb80f, BIOS settings: hdc:DMA, hdd:pio
hda: IBM-DJNA-371350, ATA DISK drive
hdc: CD-532E-B, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: 26520480 sectors (13578 MB) w/1966KiB Cache, CHS=1650/255/63
ide-cd: passing drive hdc to ide-scsi emulation.
Partition check:
hda: hda1 hda2 hda3 hda4
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
RAMDISK driver initialized: 16 RAM disks of 100000K size 1024 blocksize
Cronyx Ltd, Synchronous PPP and CISCO HDLC (c) 1994
Linux port (c) 1998 Building Number Three Ltd & Jan "Yenya" Kasprzak.
SCSI subsystem driver Revision: 1.00
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
Vendor: TEAC Model: CD-532E-B Rev: 1.0A
Type: CD-ROM ANSI SCSI revision: 02
Attached scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0
sr0: scsi3-mmc drive: 32x/32x cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.12
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 8192 buckets, 64Kbytes
TCP: Hash tables configured (established 262144 bind 65536)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 477k freed
EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
VFS: Mounted root (ext2 filesystem).
NCR53c406a: no available ports found
aec671x_detect:
scsi: <fdomain> Detection failed (no card)
megaraid: v1.18 (Release Date: Thu Oct 11 15:02:53 EDT 2001)
megaraid: no BIOS enabled.
DC390: 0 adapters found
Failed initialization of WD-7000 SCSI card!
ISO 9660 Extensions: Microsoft Joliet Level 3
ISO 9660 Extensions: RRIP_1991A
Welcome to cloop v0.65
cloop: /cdrom/KNOPPIX/KNOPPIX: 28188 blocks, 65536 bytes, largest block is 65562 bytes.
ISO 9660 Extensions: RRIP_1991A
Freeing unused kernel memory: 124k freed
Real Time Clock Driver v1.10e
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16)
Linux Kernel Card Services 3.1.22
options: [pci] [cardbus] [pm]
Intel PCIC probe: not found.
Databook TCIC-2 PCMCIA probe: not found.
unloading Kernel Card Services
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-uhci.c: $Revision: 1.275 $ time 17:03:11 Aug 3 2002
usb-uhci.c: High bandwidth mode enabled
PCI: Found IRQ 9 for device 00:04.2
usb-uhci.c: USB UHCI at I/O 0xb400, IRQ 9
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
usbdevfs: remount parameter error
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI ISAPNP enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
parport0: PC-style at 0x378 [PCSPP,TRISTATE,EPP]
parport0: irq 7 detected
Soundblaster audio driver Copyright (C) by Hannu Savolainen 1993-1996
sb: Creative ViBRA16X PnP detected
sb: ISAPnP reports 'Creative ViBRA16X PnP' at i/o 0x220, irq 5, dma 1, 3
SB 4.16 detected OK (220)
SB16: Bad or missing 16 bit DMA channel
sb: 1 Soundblaster PnP card(s) found.
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 564M
agpgart: Detected Intel 440BX chipset
agpgart: AGP aperture is 64M @ 0xe4000000
Adding Swap: 248996k swap-space (priority -1)
>
> ・ifconfig -aの出力結果でeth0の部分
$ifconfig -a
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:366 errors:0 dropped:0 overruns:0 frame:0
TX packets:366 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:26577 (25.9 KiB) TX bytes:26577 (25.9 KiB)
のみです。
どうもeth0が無いようです。
ためしに
$ping 127.0.0.1
としたら、応答が帰ってきました。
アドバイス、宜しくお願いします。